Topic

Caldera Keg

  • This topic is empty.
Viewing 20 posts - 1 through 20 (of 20 total)
PostedAug 27, 2008 at 8:51 pm

What do you guys use to remove the keg from the cone? Would I need to add a pan grabber to get it out? Is the keg to hot to touch. Is there any other good ways to use esbit fuel with a beer can pot?

PostedAug 28, 2008 at 1:14 pm

Do you have the silcone ring? That should be cool enough to touch. If not, then anything along the lines of possum down mitts/gloves, or wool socks can be used as a hot mitt.

Mark Hurd BPL Member
PostedAug 28, 2008 at 8:30 pm

Why take it off? If the can does not slip out of the cone I just pick up the whole assembly and pour or mix or do whatever with the cone still attached. When it cools off the can usually just slides out of the cone. I have not found the cone to get in the way. YMMV.

-Mark

Monty Montana BPL Member
PostedAug 28, 2008 at 9:13 pm

You could go with a Ti Esbit wing stove paired with a Ti foil wind screen, both from BPL; however, the small diameter of a beer can is less effecient at catching all the flame than a larger diameter pot, which means a longer boil time and more fuel used. I prefer this set up to using Esbit in my Caldera Cone because I don't want it to get all gunked up from the infamous Esbit residue; hence, I burn only alcohol in the Cone.

Rand Lindsly BPL Member
PostedAug 30, 2008 at 5:42 pm

If you aren't comfortable handling it by the silicone ring, the included cozy is perfect for grabbing the can.

Rand

PostedAug 30, 2008 at 8:02 pm

Rand, are there any plans in the mix to make a system with the heineken can? I like the shorter/fatter stance of that can a little better. Looking at one I have here if you extruded a lip in the fattest part of the top of the can then the cone would work despite the fat part at the bottom that is the same diameter. The only other problem I've found is the caddy is a little too narrow. Are there wider and shorter caddies available to you for this application? By the way, extruding the lip where I mentioned is right at where it would need to be to keep 2 cups under the cone.

PostedAug 31, 2008 at 3:23 pm

I wrapped the top bulge of the Heine can with fiberglass wick. This gives my MYOG Cone purchase to hold the can and gives me something to grab it with. Sometimes the cone comes away with the can, but I have this occurring on even the Caldera Cones. Within seconds it's cool enough to pull away.

My cone is made from oven liner and folds up into a 4" square'ish shape for compact packing. Yes, the aluminum crimps and tears small holes over time, but I have my pattern and can make a new one within 10 minutes.

MYOG can and cone

todd BPL Member
PostedAug 31, 2008 at 7:30 pm

Nice! Care to share your pattern?

Todd

PostedSep 1, 2008 at 9:10 am

Lemme work on that Todd. It's a large paper pattern, too large for a scan. But I'll dust off those drafting lessons, get the arc's and lengths and see what I can come up with. I've also been wanting to enlarge the base circumference to provide more oxygen.

-Michael

PostedSep 2, 2008 at 11:04 am

that link is very helpful. but after experimenting with making one, I hope TD makes one for the heine keg. The cone came out ok but with the tools I have I can't get the specs tight enough; and shelling out money for a set of digital calipers and a digital compass big enough to make the cones kind of defeats the price point of the cone system.

PostedSep 2, 2008 at 11:05 am

But nothin'!!!! I've seen a couple other attempts at a pattern calculation but it didn't work for me. I'm going to try this right away!

I even have a sheet of titanium awaiting the final pattern and wood fire tests.

Thanks loads Ken!

-Michael

PostedSep 2, 2008 at 11:14 am

Honestly, I don't believe it needs to be within such tight measurements. Neither my bottom nor my top edge is flush with the ground or the lip of the keg, or pot. It doesn't appear to matter for stability, load bearing, or heat transfer. I've fairly extensively field and home tested both the Caldera and MYOG.

Once you establish a pattern, the best thing about MYOG and using oven liner, is you can fold it and amke a new one when it wears out. The single largest complaint of the cone is pack-ability. Well, no worries with a 4" square of aluminum. Maybe I'll do a photo or video demonstration. Ugh, video. Next I'll have a cam site and a MySpace page. ::grin::

-Michael

PostedSep 2, 2008 at 12:08 pm

maybe I'll have to give it another whirl. I need to go get some thicker material though. I'll have to try some tooling foil or titanium foil from tigoat. Any other suggestions for material? I could probably make it short enough to fit inside the keg itself; the purpose is really for a windscreen that is also a stand so the whole pot doesn't need to fit inside the cone. I saw a thread on another forum about using a lifesavers fruit tarts lid as a lid for the heine pot; looked pretty sweet, nice tight fit and you don't need to take it off to pour. Should hold things in well. I'll post some pics when I get ahold of one.

John Roan BPL Member
PostedSep 26, 2009 at 9:22 am

I use my Smartwool glove liners to pick mine up. Multi-use item!

PostedSep 26, 2009 at 9:38 am

Couldn't one make adaptors for a Caldera Cone's top that would permit the use of different sized pots? This would be an adaptor that stays on the C.C, not on the pot.I ask B/C I'm seriously thinking of getting a C.C. Inferno version for wood fires. But if I'm limited to just one size of pot that's a deal breaker.

Being restricted to just ONE size pot seems a very limiting design.

Eric

John Roan BPL Member
PostedSep 26, 2009 at 9:41 am

"Being restricted to just ONE size pot seems a very limiting design. "

But an ingenious way to get you to purchase more than one! I have two + an inferno!

Rand Lindsly BPL Member
PostedSep 26, 2009 at 1:05 pm

Yes….in theory one could come up with a way to make adapters for the top of the Caldera Cone to adapt to different pot sizes. The adapter would need to not only adapt the diameter of the second pot to the diameter of the top of the cone, but also the height offset above the stove. Also, you would have to come up with a way to deal with the handle. In most of the knee-jerk designs I’m thinking of at this moment, the handle would have to cut through the entire adapter making it either useless, or an arbitrarily more complex design that could pass a handle AND be stiff enough to hold the pot firmly. Then, once you start making it stiffer/more rigid, packability becomes an issue in that it will likely not roll/fold in some obvious way.

All of that are just design thoughts…..the real issue is that we currently support in the neighborhood of 58 different cones/pots. Mathematically, if we were to start making adapters from every cone to every other pot, you get into a combination/permutation type nightmare. Without tweaking and eliminating corner case scenarios and adaptations, or getting into a big math lecture on combinatorial mathematics, 58 different pots would lead you down the road toward 1653 different adapters. Again, not exactly correct, but the right order of magnitude I believe.

So, if you could come up with a design that actually worked, the back of the envelope calculation of the number of SKUs you might be exposing yourself to support gets out of hand pretty quickly.

Now, with that said, we did just release the Caldera UL Compact that is usable across a variety of different pots…..and we are thinking about turning that into a wood burner as well. Haven’t gotten that far yet….but it’s looming. (Note, the ULCompact is not as efficient as the standard Caldera because the pot is exposed to the environment and is outside the heat-zone of the cone….but it packs inside the pot)

Finally, we did do one special MSR 1L + 1.5L combo Ti-Tri once….and might be persuaded to do others if they make sense…..but the adapter approach would need much more thought on how to make something that both works and is mathematically possible.

Rand :-)

Viewing 20 posts - 1 through 20 (of 20 total)
Loading...