Topic

RidgeRest Mod Ideas

  • This topic is empty.
Viewing 10 posts - 1 through 10 (of 10 total)
PostedNov 10, 2014 at 8:00 pm

What are some different ways people have modded a RidgeRest for dual use as a pack pad? I've got a GG mariposa and a small ridge rest and am thinking to cut a bit off the end long enough to fold in half and use as the back pad and then at night just have that piece to make the pad it's normal length. Any reason why making the "back pad" section just single width? Will folding it be fine?

Obviously impossible to try out without cutting it first, but maybe I'm just overthinking this…

Brian Hall BPL Member
PostedNov 10, 2014 at 8:08 pm

Just make a cylinder with it so it acts as a frame, then stuff everything else inside of the cylinder. Only problem is that it does cut down on the volume of the pack.

James Cahill BPL Member
PostedNov 10, 2014 at 10:41 pm

Another vote for the cylinder method, although it may feel a little funny on your back depending on your pack (I don't notice). I find it much easier to pack than trying to fiddle with folding it, and it keeps all the awkward hard objects in check. I put my pack liner inside of it to make things easier to slide in and out. I also bought one of those cheap blue foam pads because they're wider and I needed the "frame" to reach my shoulder straps.

Jerry Adams BPL Member
PostedNov 11, 2014 at 6:58 am

cylinder++

makes your pack one solid mass that doesn't shift so much as you walk along. and resists torso collapse

David Chenault BPL Member
PostedNov 11, 2014 at 9:44 am

A ridgerest cut to fit, folded, in a Gorilla or Mariposa is a great mod. A little more structure than the stock sitlight, and makes a nice camp pad and underfoot insulation while sleeping.

PostedNov 11, 2014 at 9:57 am

Burrito method works well in my GG Gorilla. It does use up a lot of volume though. So i cut a bottom portion off the pad, folded it in half once, and put it in the exterior pad sleeve against my back. It felt comfortable against my back. May be able to even have it in 3rds in the pad sleeve, however that might be pushing it.

PostedNov 11, 2014 at 1:37 pm

It's funny, I've read about using that method before but for some reason didn't even have it cross my mind here.

In the Mariposa I have found that the stock Small pad overlaps quite a bit. I am planning an AT thru hike, and with a quick "mock pack" of the bag, everything fits fine. I do still like the idea of having a separate pad in the back so that i can remove it quickly for use as a sit pad during breaks. Also works great as a way to fan the flames of a budding fire.

If I remove the aluminum stays (frame), back pad and hipbelt I can save 11.2 ounces as well. With a UL load the frame is not needed and the pad (even uncut in the pack itself) works well enough as a back pad. I'd love to test this method without cutting the pad first but I'm injured and antsy…will probably just go cut it when I get home!

Will post pics and thoughts if so

PostedNov 11, 2014 at 1:43 pm

I've got some velcro straps i could cut off the leg brace i've been wearing as well to keep the two pad sections attached at night. Some super glue should do the trick!

PostedNov 13, 2014 at 11:54 am

was able to do the back pad mod and it works perfectly. First I cut off the branded "tab" at the end of the pad so the backpad would have uniform texture. Measured out the length of the pad that would make one circle around the inside of the pack without overlapping and cut off the other side. It was still a little too wide for the pack pad so I trimmed it just a bit. It is a little wider than the pad that came with the pack but fits perfectly.

The sleep pad length is just enough for a pad that runs from my shoulders to just past my butt. Of course I can add the backpad part of it to the end and make it a bit longer/warmer.

Highly recommended mod!

Viewing 10 posts - 1 through 10 (of 10 total)
Loading...