Topic

Jetboil sol Ti question

  • This topic is empty.
Viewing 10 posts - 1 through 10 (of 10 total)
PostedApr 3, 2012 at 9:21 pm

I just got a jetboil sol Ti with my REI dividend. Did a test boil and it's pretty impressive how fast it boils.

I'm wondering if owners of this stove can chime in on the valve as I'm not sure if the one on my stove is faulty.

When I start to open the valve it works normally, with the flame and gas flow gradually increasing, but then at approximately one full turn open the gas flow and the flame starts to decrease for half a turn or so and then starts to increase again. It does this with the stove lit or not lit. In other words, while gradually opening the valve the flow will increase, then decrease, then increase again.

This does not seem right to me.

PostedApr 4, 2012 at 6:03 am

Seems weird. Try it with another canister of fuel to verify it isn't the can?

PostedApr 4, 2012 at 6:53 am

It's not the can. It's nearly full and I hooked up my snowpeak gigapower canister stove to it and it works normally.

I think I'm going to return my stove. I also noticed that the valve regulator seems loose, ie when it's partially open It has quite a bit of play where it enters the stove body.

PostedApr 4, 2012 at 7:44 am

I'd take advantage of REI's great policy and take it back and try another…

Hikin’ Jim BPL Member
PostedApr 4, 2012 at 8:10 am

I’ve played with a couple of the Sol burners. Yours sounds a little weird. Probably no big deal, but you might take it back just to be safe.

I took my old Jetboil PCS burner out the other day. The PCS feels really klunky compared to the new Sol burner. The one thing I notice about the old PCS burner though is that the valve action is smooth and continuous. The Sol’s valve action down in the low range is really wonky. Turn it up and the flame goes down. But unlike your burner, the wierdnesses that I encountered were all on very low flame settings.

HJ
Adventures In Stoving

PostedApr 4, 2012 at 12:02 pm

I've decided I'm going to exchange it for another. Yes, it doesn't sound normal.

On another note, the instructions say to use a medium heat setting. Do you guys/gals set it on full blast or something in between?

PostedApr 4, 2012 at 12:25 pm

I never use mine on full blast – low to medium for me. Seems to boil plenty quick for me at that. Usually by the time I dump my Via and some creamer/sugar into my cup, the water is already at a full boil…

Hikin’ Jim BPL Member
PostedApr 4, 2012 at 12:26 pm

Daniel,

I think you should take any warnings from Jetboil seriously. There have been some problems with the aluminum heat exchanger on the Ti pot melting.

Now, is that happening right and left all the time? No, but that’s an awfully nice, expensive piece of gear. Again, I’d take what JB says seriously. More on the issue of Jetboil Sol Ti heat exchanger melting.

HJ
Adventures In Stoving

PostedApr 4, 2012 at 2:10 pm

Yes its a dud, hope REI has stock to swap for you quickly.

the supplied 0.8L pot comes to boil so very fast at full throttle you can boil over in a daydream, have it mid-way down.

full-throttle would be a hurry boil need if say you used the pot support and a larger pot or if you bought say the Sumo companion cup for group. Or say in very cold conditions as the pot will be radiating its heat away and risk taking more fuel to get to a boil.

There's plenty of water boiling videos out there, this was my first attempt.
http://www.youtube.com/watch?v=X5RwQwy8524&feature=player_detailpage#t=154s

Viewing 10 posts - 1 through 10 (of 10 total)
Loading...