Topic

Replacement lid for BPL550 pot?


Forum Posting

A Membership is required to post in the forums. Login or become a member to post in the member forums!

Home Forums Gear Forums Gear (General) Replacement lid for BPL550 pot?

  • This topic is empty.
Viewing 14 posts - 1 through 14 (of 14 total)
  • Author
    Posts
  • #1285883
    todd
    BPL Member

    @funnymo

    Locale: SE USA

    Anyone found a lid to replace the stock lid? Specifically, a plastic lid that will snap in place?

    Thanks!

    Perhaps this should be in MYOG…I dunno.

    #1841723
    Dan @ Durston Gear
    BPL Member

    @dandydan

    Locale: Canadian Rockies

    It doesn't snap on, but the Ruta Locura carbon fiber lid for this pot is 7 grams.

    #1841798
    Franco Darioli
    Spectator

    @franco

    Locale: Gauche, CU.

    550ml CF lid

    #1841833
    todd
    BPL Member

    @funnymo

    Locale: SE USA

    Great pic Franco! Thanks. That's the same lid Dan referenced, correct?

    #1842215
    Franco Darioli
    Spectator

    @franco

    Locale: Gauche, CU.

    yes, it is..
    I use that instead of the original not because it's lighter but because it stays on and it is cool to the touch .
    Franco

    #1842218
    P. Larson
    Member

    @reacttocontact

    Foil. I'm surprised nobody has said foil.

    Franco: You bought a carbon fiber lid?!?!?! =)

    #1842377
    Andrew Klinzmann
    Spectator

    @aklinz

    Does anyone know if there are larger carbon fibre lids available ? I am looking for one to fit my JetBoil Sumo, which has a diameter of 4.9 inches.
    Andrew Klinzmann [email protected]

    #1842385
    Dan @ Durston Gear
    BPL Member

    @dandydan

    Locale: Canadian Rockies

    I talked to Ruta Locura about making a bit larger ones because I wanted one for my 0.9L Evernew pot (4.3" diameter) but they said they have no plans for larger lids. I ended up switching to a narrower pot.

    #1842533
    Eric Blumensaadt
    BPL Member

    @danepacker

    Locale: Mojave Desert

    I made a lid for my 1 L. pot from the heavy duty "foil" of a disposable aluminum pie pan. I used automotive foil muffler tape to attatch a ring handle in the center. The handle can lay flat when packed.

    The lid stays on B/C I pressed the 1/4" overhang down around the pot top edge and then turned 1/2 of the raw edge up into itself.

    #1858675
    Ben Whitsett
    Member

    @benwhitsett

    Eric,

    Pictures please!

    #1889710
    Ole Saether
    BPL Member

    @osaether

    Locale: Norway

    I don't know if the diameter of the BPL550 is the same as for the 550-SUL but I have cut the bottom of an Ass Kickin' Snack Mix can and used it on the 550-SUL. The diameter is perfect but the weight savings is only 8 grams (0.28 oz).

    Ass Kickin' Snack Mix canBPL Firelite 550-SUL

    #1954603
    michael levi
    Member

    @m-l

    Locale: W-Never Eat Soggy (W)affles

    Any new pictures you guys want to share of your carbon lids?

    #1954867
    Mark Fowler
    BPL Member

    @kramrelwof

    Locale: Namadgi

    This is Ruta Locura lid with their 550ml mug. I added a reflexit insert and a handle using silicon tube and a bit of cord.pimped cf lid

    #1954871
    Bob Gross
    BPL Member

    @b-g-2-2

    Locale: Silicon Valley

    Here is the MYOG carbon fiber lid.

    sheet carbon fiber lid

    The handle is silicone string, wired on and epoxied on.

    –B.G.–

Viewing 14 posts - 1 through 14 (of 14 total)
  • You must be logged in to reply to this topic.
Forum Posting

A Membership is required to post in the forums. Login or become a member to post in the member forums!

Loading...