Topic

Duomid guyline

  • This topic is empty.
Viewing 8 posts - 1 through 8 (of 8 total)
PostedApr 28, 2010 at 10:08 am

Just got my new silnylon duomid from MLD in the mail.

I pitched it last night in the backyard using my aircore guylines from my previous ponchotarp. After playing around with it for a few minutes I got it pretty taught, but it left me wondering: before I hack up the supplied line, what length guylines do you duomid users have?

Corners? side-panel tieouts? mid ground-level tieouts?

PostedApr 28, 2010 at 10:31 am

I'm using about 15" for the corner tie outs and then I think I used 60" combining the mid panel and mid-ground tie outs into a single loop.

Works well. Here's a pic of Andy Howell's setup. I've got a "breen" stealth cuben version but had it setup the same way with my sil version. Allows easy tension/retensioning from inside the shelter.

Andy's Duo

I'm actually using Ron's Liteline on mine right now. Seems to be holding tension. Not sure how well the linelocs will handle the 1.5mm line though. Might go to 2mm.

PostedApr 28, 2010 at 11:18 am

Nice idea for the loop. I'm gonna do that to mine! Thanks!

My lengths right now are set for exactly what Ron recommends. Pitches fine for me so far.

Zack h BPL Member
PostedApr 28, 2010 at 11:35 am

I feel a little left out…

where did you all get Ron's recommendations?

PostedApr 28, 2010 at 3:17 pm

Thanks. Though I havn’t read anywhere about Ron’s recommended lengths, I e-mailed him, and he always gets back quick.

Eric, I am very interested in trying out that loop, seems like a great idea. Do you keep the length connected to the mid-panel tieout fixed, or does it change when tightened with the linelocs?

PostedApr 28, 2010 at 3:28 pm

Hi Dan,

Do you mind sharing what Ron said about recommended guy line lengths?

His web page for the Duomid states that most of the time the 4 corners would want to be pegged close to the ground and then pull the mid points on the long side out to form “eyebrows” for ventilation.

I should check my pole height as well as I can’t seem to get a really good pitch on my older molder Duomid. I need to try it sometime before it is getting dark and raining and I am hungry and cold. I have only ever used my Duomid solo, so even with my poor pitch I still have plenty of room and stay warm and dry.

PostedApr 28, 2010 at 9:01 pm

My Mistake! I thought I had them set to what Ron recommended, but now I realize that only my tarp is set to the lengths he suggests.

I don't recall what the lengths are of my duomid guy lines. If I have time I will measure tomorrow.

PostedApr 29, 2010 at 6:21 am

I attached the mid panel tie outs with a loop and larkshead to the bungi. Then it passes down around my stake and through the mid panel lower lineloc as normal.

This allows me to pull tension at the lineloc and the entire line equalizes tension against the bungi. Seems to offer good tension while offering some level of protection for the fabric (in my case the cuben). For sil guys it might allow the benefit of not having to retension…

Easy to setup and requires 4 less stakes vs individual tie outs (8 vs 12). Has worked well so far.

I may go to 6' or possibly 7' for the larger front/rear panels to provide more options. In the end, you only have half the line length available for pitching (other half is the return to the lineloc).

Viewing 8 posts - 1 through 8 (of 8 total)
Loading...