Topic

titanium maintenance

  • This topic is empty.
Viewing 18 posts - 1 through 18 (of 18 total)
Bob Gross BPL Member
PostedApr 21, 2010 at 7:30 pm

I have an REI titanium Sierra cup. Somehow it has gotten some black marks, almost looking like tiny burn marks, on the inside surface. It's just a cosmetic problem. I was unsuccessfully trying to clean them off using fine steel wool and kitchen cleanser. That didn't touch the spots. Any better ideas?
–B.G.–

Eugene Smith BPL Member
PostedApr 21, 2010 at 7:33 pm

I seriously think someone on BPL recently cleaned a bunch of woodburned titanium pots with the Mr. Clean Magic Eraser pads. Seriously. Amazed me.

PostedApr 21, 2010 at 7:39 pm

Stream of consciousness WAGs –

Are the spots on the surface, or in a pit?

Perhaps impurities that have reacted with food?

They were always there, but you just noticed?

Your dog chewed on the cup and the dents reflect light differently?

ahhhh….

Bob Gross BPL Member
PostedApr 21, 2010 at 7:44 pm

The spots are on the inside surface, so they are nothing left from wood fire or esbit. They appear to be black dots from a marker, not raised or indented. They appeared only after the last trip to the field. No dog, but the cat is avoiding me right now.

I am almost tempted to use some abrasive wheel on my Dremel tool. I'm sure that I could abrade it, but I'm not sure if that might damage the surface worse than what the marks are doing.

–B.G.–

PostedApr 21, 2010 at 8:14 pm

I'm sure you've tried rubbing alcohol already so try using the orange pumice soap in your garage

Konrad . BPL Member
PostedApr 21, 2010 at 9:01 pm

Bob, you gotta try the mr. clean magic eraser. I too saw the thread that everyone else is referring to. I promptly went and picked up one and went to work on a msr titan kettle that had wood soot, etc. It took it all off! The erasers arent cheap, and sold for around 5 bucks for 2. I went through 1 whole one, but it worked. It even stripped off old black spraypaint that was coated on the titanium. It does take elbow grease though

PostedApr 21, 2010 at 10:56 pm

Keep it on there. If your pots aren't blackened and beaten, they haven't been used enough!

PostedApr 21, 2010 at 11:23 pm

Rog, thanks for asking! My shoulder is metal, titanium to be exact. I sure hope it doesn't require any maintenance!

I have been able to backpack without much discomfort. Remarkable because the shoulder strap sits right on the metal protrusion. I can't sleep on the broken side on firm ground but I can work through that.

Bob Gross BPL Member
PostedApr 21, 2010 at 11:31 pm

I've tried about every kind of solvent, cleaner, and fuel, and nothing touches it. Ordinary esbit residue comes off with white gas or Windex, but it doesn't affect this at all. So, I very carefully scratched it with a hard blade and managed to get part of it off. I still don't know what it was.

–B.G.–

Rog Tallbloke BPL Member
PostedApr 21, 2010 at 11:54 pm

To the OP, rotary brass brush in a dremel is what I'd try.

Jack, good to hear you're enjoying the trail.

Brad Groves BPL Member
PostedApr 22, 2010 at 11:13 am

Another vote for just leave it alone. It's a backpacking pot, who cares? It's supposed to look a little funky! I wouldn't use a dremel; I can easily see burning right thru the cup for a cosmetic concern.

I think it's just a little food burned into place; I've had that happen before. Eventually it'll probably wear off. Perhaps you should just try scotch, bourbon, etc in there to, um, see how many it takes to clean it out.

Gary Dunckel BPL Member
PostedApr 22, 2010 at 11:36 am

Why not try the rubber Dremel polishing wheel? The brass brush might scratch it.

Bob Gross BPL Member
PostedApr 22, 2010 at 11:43 am

"rubber Dremel polishing wheel"

Rubber?

All of the bits that I have are either metal or abrasive.

–B.G.–

Gary Dunckel BPL Member
PostedApr 22, 2010 at 11:58 am

Yeah, an emory-impregnated rubber polishing wheel (part #425). It fits onto the screw type mandrel. They'll have them at your friendly Dremel supply place. I use mine to remove Sharpie markings on my titanium MYOG stuff, and to put a final polish on the metal.

Bob Gross BPL Member
PostedApr 22, 2010 at 12:05 pm

Emory-impregnated rubber.

I guess I learn something every day.

–B.G.–

Roger Caffin BPL Member
PostedApr 22, 2010 at 5:54 pm

> Why not try the rubber Dremel polishing wheel? The brass brush might scratch it.

Brass won't damage titanium. Emery-loaded rubber can.

Cheers

Viewing 18 posts - 1 through 18 (of 18 total)
Loading...