Ron has posted pictures of a SoloMid inner tent prototype on the MLD Facebook site. This will, when paired with a SoloMid, create a double wall shelter weighing in at 1.5 lbs or under depending on SoloMid version used.
Topic
MLD Inner Tent
Become a member to post in the forums.
- This topic is empty.
The inner tent looks great…and it further increases the versatility of the solo/duo mid(s) into a 4 season UL option (especially for those who do not use a bivy). Inner net for 3 season, Inner tent for winter and/or more inclement weather conditions.
I have been waiting for someone to make one of those. I almost emailed Ron back in Dec. to see if he could make one.
Keep up the good work Ron.
Looks Great !
Nice!!
I feel this will be a very strong addition to the MLD line. I look forward to seeing pictures of the InnerTent setup with the SoloMid.
Thom:
Can you post a link please?
I do wish for additional pictures of the Inner Tent setup inside a SoloMid….but regardless, it's a great design concept :-)
Thanks, Chris.
my feeling is that it needs more through draught, take the bottom part of the door mesh and split it between the ends. Cover most mesh with 30D ripstop from the inside, adjusted with hook and loop tabs and do not have the zipped 30D door.
Derek – it is a prototype and I believe Ron would love to hear your thoughts directly.
Derek,
The InnerTent prototype is a work in progress and knowing Ron, and the MLD crew, the final production version will be dialed in for a max performance/weight ratio.
The introduction of the InnerTent will allow a user to pick and choose the best shelter set up for a given trip and expected conditions.
Great job Ron.
I'm looking forward to getting an inner tent myself. I prefer the Duo mesh inner with my Duomid, but would get the Solo inner tent for colder weather. The smaller area should be warmer.
Like Derek i would like a mesh panel at the top/front, and a mesh panel at the head and feet for ventilation. Velcro on the mesh panels so they can be closed up when wanted.
I love the pik'n mix style of the MLD 'mids. :)
Mike,
With the small mesh upper vent shown on the InnerTent prototype and with the ability to create an opening at the lower door via duel zip sliders would this not create adequate high/low venting?
I just feel that a mesh panel by your head would help lift your condensation forming breath up towards a top mesh panel and out. Your feet give off a lot of heat too. Maybe it's just that i'm used to using tents that have this. :)
Mike and Derek – I share your concern regarding the need for better air flow. My experience with my MYOG inner fabric insert was a damp one… For pictures and comments see this thread:
I would like to hear from any Hillberg Akto users regarding condensation issues in the inner fabric insert. I believe that insert has a large panel of 30D ripstop that can be pulled down on the top of the door (exposing a mesh panel. Perhaps this is all that is needed. See Moontrail’s Image: 
It is also possible that as it is, Ron has found ventilation to not be an issue?
I never had condensation inside the inner of my Akto. I think the trick to minimizing interior condensation on the Akto is opening the two end vents and top vent on the outer tent. It does a pretty good job of providing a 'chiminey' effect.
David,
Likewise with the SoloMid (or DuoMid) when used with the InnerTent. Pitching to allow for adequate air flow at the shelters ends should not be an issue, limited only by personal preference.
Thanks all for the great feedback on the proto- I do think the top mesh could be little larger. The lower door can also be vented with the dual zips.
It's all a balance of making this one for colder weather vs the all net version. I'll pour over the various ideas in a week or two before moving to the final design.
I thought Ron would read this thread so I posted here.
I do not think that windproof breathable nylon is breathable enough for an inner tent in a damp cold place like Scotland. If there is no wind you are relying on chimney effect with high low vents. If all vents are on one wall you get dampness in the unventilated cold corners.
If there is wind the mid will be pitched one end to the wind and you will get better through draught with vents at both ends. If it is very windy you have the covers to keep wind and spindrift out. I also think my suggestion would weigh less.
If there is a problem with water getting in through the mesh because the ends are flatter than the sides you could have a little vertical end mesh wall with a bit of loss of groundsheet, or put the mesh at the ends of the back wall rather than the ends themselves.
Personally I would move up to a 1/4 of the door mesh area to each end.
One thing I'm curious about – why 30D nylon instead of Momentum? Is the nylon more breathable? more water resistant? cheaper?
Derek / Chris,
I would think a first prototype of a new concept is mainly focused on size and fit. I have no doubt that Ron will, as he works through the design process for the production version of the InnerTent, end up with the best cost/weight/performance ratio as it relates to both materials used and ventilation.
When I was researching fabrics to use for my inner fabric tent I email AYCE at Thru-Hiker regarding using Momentum. He indicated it would be a poor choice. Others here at BPL suggested that it would be fine… in the end I decided to use 1.1osy uncoated ripstop to save money. Clearly Momentum would be more water resistant but at the expense of breathability? not sure..
In my opinion, water resistance is less of a concern since the inner fabric tent is covered by the silnylon tarp and the insert has a silnylon bathtub floor. My main objective was to prevent spindrift and high winds from entering the sleeping area.
Early last year, we had an informative discussion of the fabric choice for my inner fabric tent: LINK HERE
Become a member to post in the forums.

