Topic

UL Compact Caldera Cone stakes

  • This topic is empty.
Viewing 20 posts - 1 through 20 (of 20 total)
PostedJan 12, 2010 at 7:42 am

I've been weeding through my pile of various stakes trying to find one that fits those tiny holes in my new MLD Caldera Cone, but none of them fit!

Then I found a few pieces of wire from a coat hanger I'd cut up a while ago to make pot stands. One of those pieces of wire diagonally through the little holes (as opposed to two stakes cross-ways like in the pictures) seems to hold up the pot just fine. The wire isn't as multi-use as the stakes, but only weighs about 4 grams and is cheap.

Now that I've got that figured out, do you think it's worth buying a few of those vargo titanium shepard hook stakes that I see in the pictures of the UL Caldera cones?

PostedJan 12, 2010 at 7:59 am

As the old adage says, "If it ain't broke…"

My only concerns would be stability and heat resistance. The stability comment is referring to using one support diagonally. I haven't tried it but it would definitely be a less stable pot support. I can imagine the mug would tend to tilt to one side or the other. Maybe its stable enough with the close fit between the pot and cone though. The other concern is whether or not the wire gets soft enough when heated to buckle under the weight of a full pot of water. My guess would be no but you might want to do an extreme test in a controlled environment to be sure.

I'm currently using ti stakes but had a project on my list to snip down some bike spokes to use as supports. I hadn't considered using coat hanger wire.

Mark Verber BPL Member
PostedJan 12, 2010 at 8:13 am

if it works, why change. anything that is sufficent steel or titanium should work… just so long as it's not aluminium which can melt.

I am doing something even more sketchy but it's worked this season. I haven't been using anything. Rather I use the MLD850s handles extended to keep it from falling through. I haven't done detailed measurements, but it seems like it has approx as fuel efficient (maybe even a bit better) as when I use stakes which surprised me give the pot bottom is tilted to the side.

–Mark

PostedJan 12, 2010 at 12:10 pm

Ryan
I have tried coat hanger wire (several types) they all soften and bend.
Not safe enough for me.
Franco

PostedJan 12, 2010 at 2:35 pm

Mark, has your approach done any harm to the cone itself? I hadn't really thought of not using anything. I'll probably end up getting a few of those vargo titanium stakes sometime soon anyway. Those holes for the stakes are awfully small… too bad none of the stakes I already have will fit.

Brad Rogers BPL Member
PostedJan 12, 2010 at 2:37 pm

What about the Terra Nova 1g or 2g tent stakes? They might work better for that then for trying to stake a tent down!

Rand Lindsly BPL Member
PostedJan 12, 2010 at 5:44 pm

Thanks everybody for the insight! We focus mostly on the Vargo T-101 stakes. While a "snug" fit in the ULC line, they do fit. Feel free to drill out the holes a bit as suggested by Brady. Of course, be careful because the bit will want to grab the cone and spin it.

We will be opening up the holes on the next batches of cones we ship. Thanks again for the insight!

Rand :-)

Mark Verber BPL Member
PostedJan 12, 2010 at 7:09 pm

> Mark, has your approach done any harm to the cone itself?

So far no damage from not stakes. That said, it's a sketchy idea and I wouldn't be shocked if sometime in the future I would regret it. I first tried because I was lazy.

–Mark

PostedJan 14, 2010 at 5:02 pm

Thanks for listening, Rand! I just drilled out the holes in mine a tiny bit, and they now fit with some of my cheapo nail stakes. I'm planning to pick up a few of the vargo stakes anyway, but at least they'll be easier to stick in now.

I also wonder if spacing those stake holes differently might help. As I have the stakes in now, the pot just barely touches both stakes, so it's not being securely held up. I think I'll probably go with the diagonal single stake to hold the pot more securely in general. That might take some of the heat away from the pot, but at least it'll be more sturdy.

PostedJan 14, 2010 at 5:08 pm

It'd be interesting to see a picture of this. My pot sits directly on the stakes when using the Compact. If the stakes weren't there, the pot would sit further into the cone.

PostedJan 14, 2010 at 5:39 pm

No sooner asked than received! (hopefully).

Here's the cone with the stakes in.
MLD UL Caldera Cone w/ stakes

And here's the pot upended on my desk with the cone and stakes sitting on top (for a bottom view of how the stakes support the pot).Bottom view of MLD UL Caldera Cone

These stakes are cheap generic things I got at the hardware store a while ago, with a twisted square shape… I don't think this has any impact on how they support the pot. The contact with the pot is on the rounded edge of the pot, so it slips and slides a bit on the stakes.

PostedJan 14, 2010 at 5:44 pm

Not to be cheeky, but if you turned the stakes 90 degrees, would this make a difference? What I mean by that is, for each stake, feed it through the same hole you're feeding it through now, but use a different hole at the other end, but still maintaining the same type of setup you have now.

Here, I did a quick addition to your photo to show what I mean. Try putting your stakes per the red lines in this photo and see if it makes a difference.

Take care

Doug

red lines

PostedJan 14, 2010 at 6:32 pm

No regrets, of course. It's not the silliest question I've asked in public… I won't tell that story for now. I'll just chuckle to myself a bit and be happy that my caldera cone is going to be wicked awesome when I finally put it to some on-trail use.

Rand Lindsly BPL Member
PostedJan 19, 2010 at 4:36 pm

Not sure why it took me until now to realize this, but the tightness of the stake hole perforations that began this thread, is also probably explained by the fact that they were going in over the short distance. You should find them easier to install going the correct way.

Thanks for posting all this…..good to see how the gear actually gets screwed together once it leaves our shop!

Rand :-)

PostedJan 19, 2010 at 5:26 pm

Hi Rand!

FWIW, the holes are a touch tight, even going in the correct way! I find that I thread them through straight on until the tip of the stake is almost to the other side, then angle it back to the hole and finish sliding it in. Certainly not a dealbreaker for me, but a slightly larger hole would be a bit easier!

Used my Ti Compact for the first time this past weekend. I'll be using it a lot more in the future! Great product. Can't wait to try wood as a fuel source with it, just because I can!

Viewing 20 posts - 1 through 20 (of 20 total)
Loading...