Topic

Frameless Pack Questions

  • This topic is empty.
Viewing 6 posts - 1 through 6 (of 6 total)
John G BPL Member
PostedDec 5, 2009 at 10:49 am

I'm thinking of making the jump to frameless, and have some questions.

Does using the CCF pad as buritto to pack your gear into offer better weight transfer than folding the pad into layers and putting it into a pad pocket along the back of the pack ?

Is it relatively easy to remove a 3/4 ridge rest from the pad pocket during rest stops & re-insert – or is it not worth the trouble ?

Does the Ray Jardine approach of putting the food at the bottom, quilt in the middle & cloths at the top tire you out (by causing more forward lean) any more than packing the pack with the weight (food) high instead ?

Is Silnylon durable enough if you don't drag the pack around (but don't baby it a lot either) or is the Dynema fabric (or 140, or 210 pack cloth) needed ?

Thanks.

David Chenault BPL Member
PostedDec 5, 2009 at 11:00 am

I find the ridge rest burrito to be a very effective "frame", up to a bit over 30 lbs, even.

I don't use a pad pocket, but I have to think that only the external pockets have a chance of being accessible with a full pack.

I don't find sil to be even close to acceptably durable, but I beat on my packs quite a bit.

Joe Clement BPL Member
PostedDec 5, 2009 at 11:44 am

I also think that unless you have an dedicated pad pocket, you'd have to make a circle inside the pack with your pad. And I gain too much weight from these discussions, I see burrito, I have to go buy one!

PostedDec 5, 2009 at 11:59 am

I prefer the burrito even with external pad pockets. It generally sits closer to my back and carries much better this way.
With packing, the Jardine method, I think, does not work well. I pretty much pack lightest to heaviest… sleeping bag, shelter, clothes, food. Or something of that nature depending upon the particular set up.
Sil is fine if you are not off trail much and if you take care of it. It's good to have something more durable on the bottom for setting your pack down, or carry something to set it on when you stop. I use a half a piece of polycro.

Luke Schmidt BPL Member
PostedDec 5, 2009 at 1:24 pm

I pretty much pack lightest on bottom and work up from there. Usually I try to put my heaviest items (usually water bottles)right up against my back. One time I was getting sore with a very light pack and repacking stuff to balance things out helped a lot.

Tim Marshall BPL Member
PostedDec 5, 2009 at 2:49 pm

John,

There are a lot of fabrics in between 1.1silnylon and 210Dyneema. I have used 1.9oz PU or Sil nylon for the front and sides of many packs and have never had a failure (this is on trail) I have used 330Cordura and 200oxford for shoulder straps and pack back/bottom with no issues. I do think the 200oxford will fail sooner than the 330cordura, or 210Dyneema, but i don't have a pack that uses it right now and I have no long terms testing on it. These fabrics are typically the ones 210dyneema replaces, as it looks cooler, has a better name and in truth is stronger, but at a high cost.

I had the old Gregory Zpack with 140Dyneema and the pack split across the lip of my SP 600 mug (through many dyneema fibers, about a 5" tear), so dyneema isn't impervious to disasters.

I think the ULA Conduit is the best value/weight for a frameless pack with more durable fabrics.

-Tim

Viewing 6 posts - 1 through 6 (of 6 total)
Loading...