Topic

.33 Cuben

  • This topic is empty.
Viewing 14 posts - 1 through 14 (of 14 total)
Sanad Toukhly BPL Member
PostedSep 13, 2009 at 10:28 am

I've never used this weight Cuben for anything before, but I am considering switching all my stuff sacs to .33 Cuben instead of .6 Cuben. Do you guys recommend this or is it too fragile to use for stuff sacs? I've heard you can tear it with your bare hands, so I don't know if it would make a good material for a stuff sac. Let me know what you think guys.

-Sid

PostedSep 13, 2009 at 12:55 pm

Sid:
Never used .33, but I made a couple of .48 cuben stuff sacks and they are plenty strong enough. I heard that .33 was a little bit suspect for tarps, so I went with .48 for my MYOG tarp – and it seems to have worked fine! Anyway, just my 2cs worth.

Peace, James.

PostedSep 13, 2009 at 2:24 pm

Think of 0.33 cuben as if it were a very thin supermarket plastic bag (the kind in the produce section) with some spectra fibres reinforcing it. As long as it doesn't encounter anything sharp, and you make the seams with cuben tape instead of sewing it, it should be OK for most general applications.

Jim MacDiarmid BPL Member
PostedSep 14, 2009 at 7:03 am

Here’s what MLD has to say about .33 Cuben in the info regarding their .45 cuben Speed Tarp:

Long ago we prototyped the .33 Cuben and found it was unsuitable as a single layer tarp material. That .33 weight can be quite easilly ripped with your bare hands. The .45 is hard to tear without a starter cut on an edge. Our standard .60 weight is impossible to tear with bare hand and can only be torn a few inches with a good size starter cut. SO – we do not make and will not offer a .33 Cuben product.

Sanad Toukhly BPL Member
PostedSep 14, 2009 at 9:41 am

That's what I thought, I suppose going with the .45 Cuben would be best for stuff sacs.

PostedSep 14, 2009 at 1:26 pm

I made some stuff bags from cuben fiber , early white colored material from Thru-hiker. I do not remember the thickness, but it soon becomes like tissue paper in feel and its hardly waterproof if sitting in the rain outside of your pack. It becomes soft, too.It's fine for inside of the pack, however.

You might check with Granite Gear to see what they use in stuff sacks.

Jim Colten BPL Member
PostedSep 14, 2009 at 5:29 pm

Rog,

That’d be pretty interesting, especially if the price will be around $19/meter as I’ve read recently on these forums. a bit of color would make it a bit less transparent, nice for shelters … but there’s some uncertainty about how those two products match the current retail options.

Working from Cuben Tech’s product spec sheet …

If google’s calculator is correct then:
1) CT0.6K.08 @ 15.8 g/m^2 = 0.46599769 oz/yd^2
2) CT1K.08 @ 19.3 g/m^2 = 0.569225026 oz/yd^2
which is in the neighborhood of the 0.48oz/yd^2 and 0.6oz/yd^2 I see listed at Quest Outfitters and Zpacks but different enough to make me squirm a little.

Additionally, the product sheet lists the width @ 1270mm … exactly 50 inches whereas quest and zpacks list 54 inch material. The extra 4 inches is useful for what I’ve been thinking of.

Can you offer any insight into the differences?

Jim Colten BPL Member
PostedSep 14, 2009 at 5:39 pm

Frank,

I've been pretty familiar with Thru-Hiker's product line for a long time if he sold Cuben then I missed it (anything's possible there). He did sell white silicon impregnated 0.7oz/yd^2 polyester for a couple years until the most recent similar product (grey SpinnTex EXP).

John Roan BPL Member
PostedSep 14, 2009 at 7:48 pm

Not sure what weight was used on my SMD Refuge X, but it does puncture very easily. Holds up well to wind though. I wouldn't use it for stuff sacs with anything pointy (is that a word?)

PostedSep 14, 2009 at 8:11 pm

Jim, You are probably right. It is probably an earlier version of spin cloth, not cuben fiber. New, it had the feel of spin cloth, not silnylon. It was not as stiff as the recent spinn cloth, however. I'll e-mail AYCE.

Rog Tallbloke BPL Member
PostedSep 14, 2009 at 11:18 pm

Hi Jim,
Jon's email says coloured cloth is +10% on price, which is what I calculated.

The weight given on the .pdf spec sheet Jon attached to his email for CT1K.08 is 17.4g/m^2 which he stated as being 0.51oz/yd. Width is stated as 54"

Hope this helps.

PostedSep 15, 2009 at 8:49 am

Jim: You were right. Thru-hiker confirmed the white cloth I referred to was spinntex, not cuben. Sorry.

Steven Evans BPL Member
PostedSep 15, 2009 at 12:59 pm

Hey Sid,
Just saw this. I have stuffsacks, a bivy, and a tarp made out of the .33 oz cuben…I would be hesitant to recommend it to anyone who won't "play nice" with it. I find the .6 stuff to be pretty bomber.

Steve

Viewing 14 posts - 1 through 14 (of 14 total)
Loading...