Topic

packing 2L platy bottle

  • This topic is empty.
Viewing 10 posts - 1 through 10 (of 10 total)
PostedJun 15, 2008 at 11:28 pm

For those who use 2L platy my question is how do you pack it?

I think there are only two possible places: inside the backpack and on the outside back pocket/compression cord. If you put in back pocket woulndnt your pack pull away? or no? any advice?

Thanks.

Rod Lawlor BPL Member
PostedJun 16, 2008 at 2:26 am

Huzefa,

I generally put mine in/on last, just under the top pocket. I like to keep it out of the sun, to keep the contents a little cooler, and out of the main pack, to minimise problems if it leaks.

Rod

PostedJun 16, 2008 at 6:49 am

Ron, you mean under the lid? I didnt think of that..

Ok let me propose two situations where I am wearing a bivanorak which is also my pack cover for protection from rain and abrasion:

>it is raining and to access the platy I will have to remove my pack which will get wet.

>it is cold, windy outside and I need water to remain warm atleast somewhat near body temp. I have to either use bottle cozy(=weight) or keep it close to my back (= access is not super easy).

Is there a good way to integrate 2L platy bottle?

PostedJun 16, 2008 at 8:03 am

I carry mine in the front pockets of my Aarn pack. It is easily accessible and the water, which is heavy, balances the pack behind effectively. If I were you I would engineer 2 pockets on your hip belt, also attached to the front shoulder straps to take 2 x 1 litre bladders set vertically. The attachment to the shoulder straps should stop tall pockets falling forward.

PostedJun 16, 2008 at 8:21 am

I typically use mine, with a tube, as a hydration bladder in the pack right next to my back (with the foam backpad in the pack). Seems comfortable carrying that weight high and inside the pack.

John Brochu BPL Member
PostedJun 16, 2008 at 12:13 pm

I use the ULA Conduit and if I have a full load I place my bladder in one of the side mesh pockets, if not I place it at the very top of the inside compartment after rolling down the poly pack liner.

PostedJun 16, 2008 at 3:07 pm

I've carried it inside of the pack, and also in the rear mesh pocket. I could feel some effects from the weight being so far away from my body when using the mesh pocket, but it didn't seem too bad…it's not THAT far back there.

Additionally, I'm usually either using that water first, or tanking up for a dry camp that's coming up soon so I haven't really needed to carry the full bottle very far….usually just a few miles or so.

PostedJun 16, 2008 at 3:09 pm

Huzefa,

Just re-read the posts and picked up your example. Can't use a bladder?

If not, you're going to have to carry a smaller bottle (maybe one strapped on to the shoulder strap AR style) and decant out of the 2L from time to time.

Roger Caffin BPL Member
PostedJun 16, 2008 at 4:14 pm

> it is raining and to access the platy I will have to remove my pack which will get wet.
?? When it is raining I rarely drink at all. Enough water is coming inwards … :-)

>it is cold, windy outside and I need water to remain warm at least somewhat near body temp.
Poncho over the pack and me – keeps the pack a little warm from my body heat.

Cheers

PostedJun 17, 2008 at 9:45 pm

Thanks for all the comments.

Derek, a comfortable waist belt will mean -extra weight.

A hydration bladder with a tube weights 3.5oz+ (platy hoser) compared to 1oz platy bottle.

For now I am considering Russell's suggestion of carrying a smaller 16oz bottle. But this setup depends on how the the upcoming redesigned mUV water purifier works with platy bottle. I contacted them few days back and they said it will work with two liter soda bottle but werent specific about platy.

Viewing 10 posts - 1 through 10 (of 10 total)
Loading...