Topic

food rehydration container?


Forum Posting

A Membership is required to post in the forums. Login or become a member to post in the member forums!

Home Forums Gear Forums Gear (General) food rehydration container?

  • This topic is empty.
Viewing 11 posts - 1 through 11 (of 11 total)
  • Author
    Posts
  • #1237762
    Chris Nott
    Spectator

    @chrisn

    Locale: Canada west coast

    I'm in need of a watertight container that I can use to rehydrate food while on the trail. Around 12-14oz capacity. I just did a test with a Gladware container and, while it seemed watertight, shaking it (it's going to be shaken on the trail) cause it to lose some drops so it's out of the running. Candidate containers need to handle heat (just under boiling), won't lose water when shaken or subjected to 3000' elevation changes. Need not be too sturdy as it will be protected in the pack. Any suggestions?

    #1513946
    Sarah Kirkconnell
    BPL Member

    @sarbar

    Locale: Homesteading On An Island In The PNW

    Ziploc makes a version that has a twist on lid. Try those out! They are of the right size and microwave safe….

    #1514115
    Millette Jones
    Member

    @ttaboro

    Locale: Southeast

    I've tried those twist on lids for the Ziploc 2 cup container and they do allow a bit of liquid out when shaken…too bad cause they are fairly light.

    Watching this with interest as I too am interested in what others are using.

    #1514142
    Scott Bentz
    BPL Member

    @scottbentz

    Locale: Southern California

    Not the lightest, but Nalgene makes a wide mouth 16 oz. bottle that has a screw in lid that allows no leakage.

    #1514154
    Franco Darioli
    Spectator

    @franco

    Locale: Gauche, CU.

    I have a 600ml mug that has a leak proof lead and a steam valve. With 500ml of boiling water in it , the lid pops up a bit but still remains tightly on. It is a Decor container , about $5. (I think made with polypropylene )
    Not light at 85g/3oz, but maybe a lot easier to clean and more robust than the Ziplocks.
    You would need to do some shake tests…You could cut the handle off, or get one of the bowls.
    For the Twist And Loc containers, maybe a piece of bicycle tyre tube could make the lid "watertight" ?
    Franco
    Decor mug

    #1514201
    Sarah Kirkconnell
    BPL Member

    @sarbar

    Locale: Homesteading On An Island In The PNW

    On the threads of the container use teflon tape (plumbers tape).

    #1514369
    Lynn Tramper
    Member

    @retropump

    Locale: The Antipodes of La Coruna

    The Caldera Caddy is wonderful.

    #1514388
    george carr
    BPL Member

    @hammer-one

    Locale: Loco Libre Gear

    The Nalgene Canteen has a wide mouth screw on lid, is watertight, and can handle boiling water.
    Nalgene Canteen

    #1515496
    Chris Nott
    Spectator

    @chrisn

    Locale: Canada west coast

    Thanks Sarah! I got a Ziploc screw-top container, verified that it does leak when shaken but added some teflon tape to the screws and it works perfectly. And nests in my pot with my cup inside quite nicely.

    #1515512
    Sarah Kirkconnell
    BPL Member

    @sarbar

    Locale: Homesteading On An Island In The PNW

    Great! :-) Good to hear!

    #1525790
    Chris Nott
    Spectator

    @chrisn

    Locale: Canada west coast

    Just a follow-up on my use of the Ziploc screw-top container with a teflon tape seal. Indeed it does work in practice. However, I find that I have to replace the teflon tape after each trip. The tape can only be applied to the screws on the container and not the lid because it doesn't actually stick (it acts like food wrap in that tension is important). Putting on and taking off the lid abrades the tape enough to wear it away in some places after about 10 times then it will start to leak. I usually get some water pretty hot, pour it and the dehydraded food in the container and put the lid on right away. The air in the container will cool and create a seal which prevents leaking. But try not to handle the container (ie put it in your pack) until it has a chance to cool a bit because the plastic is pretty maliable when it is warm and you can easy cause a leak if you jam it the wrong way. Buy the narrow teflon tape if you want to use this system – you only need to seal the screws and anything wider is a pain when you are washing it out.

Viewing 11 posts - 1 through 11 (of 11 total)
  • You must be logged in to reply to this topic.
Forum Posting

A Membership is required to post in the forums. Login or become a member to post in the member forums!

Loading...