Topic
8-figure burner head gas stove
Forum Posting
A Membership is required to post in the forums. Login or become a member to post in the member forums!
Home › Forums › Gear Forums › Make Your Own Gear › 8-figure burner head gas stove
- This topic is empty.
-
AuthorPosts
-
Aug 15, 2007 at 8:47 am #1224610
最下のバーナーヘッド、Φ1.2mm brass pipe 0.3mmの銅線を巻き付けてあります。炎の安定化と拡散効果のためです。予熱パイプ部分を8字状に加工して、予熱性能を最も向上させています。重さは、約3gです。200ccを80秒で沸騰。焼きなまし、あえて行いません。強度を保持するためです。予熱性能はパイプが細いほど優秀になる傾向があります。接続チューブはΦ1mmのシリコンチューブを使っています。床面から鍋底まで、25mmぐらいが実験結果では最適です。高さ50mmまでは使えますが、あまり背が高いのは不利でしょう。
The burner head of the lowest, the copper wire of φ1.2mm brass pipe 0.3mm is wound. It is because of the stabilization of the flame and spread effect. Processing the preheating pipe part to 8 letter conditions, most it has improved preheating efficiency. Weight is approximately 3g. 200cc it boils in 80 seconds. Annealing, being able to meet, it does not do. Is in order to keep strength. As for preheating efficiency the extent where the pipe is thin is a tendency which becomes excellent. The connected tube uses the silicon tube of φ1mm. About 25mm with the experimental result is optimum from the floor face to bottom of a pan. You can use to height 50mm, but it probably is disadvantageous for the back to be high excessively,
Aug 15, 2007 at 9:12 pm #1398780Nice work Yukiosan,
your stove just keep getting smaller.
Tony
Aug 18, 2007 at 10:04 pm #1399162Thank you! Tony
内訳、SP300チタンカップは改良してハンドルを持ち上げ式に変更して在ります。45g。そして、自作の0.1mm厚みのフタ、およそ4gです。ステンレス製のスタンドは、7gです。ライター用のガスボンベ40g入りは缶を含んで、60gです。流量調整は事務クリップで挟む方法が簡単です。右側の赤い輪は、ガス抜き用のキャップです。赤い小物部品と共に、ボンベの同梱品です。日本では、このボンベは@¥300程度で買える一般的な商品です。1 カップモジュールとは、200mlのお湯を沸かすガス給湯システム全体を指しています。軽量な袋入り食料の場合に、加えるお湯の量は200mlで済むので、一度に沸かすのは200mlで充分です
、、、、、、、、、、、、、、、、、、、、、、、、
When titanium wind prevention 10g and the like is added, it is 147g altogether system.Breakdown, the SP300 titanium cup improving, raises the steering wheel and is modified in formula and increases. 45g. And, the cover of original 0.1mm thickness, it is approximately 4g. The stand of the stainless steel make is 7g. The chemical cylinder 40g entering for the lighter/writer including the can, is 60g. As for flow adjustment the method of putting with the office work clip is simple. The wheel where the right side is red is the cap for breathing. With the red small article part, it is the bundled item of the cylinder. In Japan, as for this cylinder it is the general commodity which can be bought with the @300 yen. 1 cup modules, it points hot water supply system to the whole gas which boils the hot water of 200ml. Because in case of the lightweight sack entering food, the quantity of the hot water which is added is sufficient 200ml, it is sufficient with 200ml to boil at one time.
Aug 19, 2007 at 2:59 pm #1399222Very nice Yukiosan. Very well done and easily understood. Photos are very nice. You are an inspiration for future stove making, thank you!!!!
Dan
Aug 19, 2007 at 7:54 pm #13992508-figure burner is real unique work and well made,it is very great for so small a gas burner to boil 200ml water only in 80 second!
-
AuthorPosts
- You must be logged in to reply to this topic.
Forum Posting
A Membership is required to post in the forums. Login or become a member to post in the member forums!
Our Community Posts are Moderated
Backpacking Light community posts are moderated and here to foster helpful and positive discussions about lightweight backpacking. Please be mindful of our values and boundaries and review our Community Guidelines prior to posting.
Get the Newsletter
Gear Research & Discovery Tools
- Browse our curated Gear Shop
- See the latest Gear Deals and Sales
- Our Recommendations
- Search for Gear on Sale with the Gear Finder
- Used Gear Swap
- Member Gear Reviews and BPL Gear Review Articles
- Browse by Gear Type or Brand.